Search Inventory
Search Products & Site
Features
Features | Benefits |
Surpassed rugged industry standards |
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures specified by ANSI. |
Factory assembled | Saves customer set-up time and money. |
Fully welded deck | Fully welded deck adds strength. |
250 HP Divider gearbox 210 HP center & wing gearboxes |
A rugged heavy built gearboxes capable of handling heavy cutting applications. |
Gearbox seal protection | Gearbox bottom seal protection for longer bearing life. |
Input driveline: Cat. 6 CV |
Holds up to shock loads and harsh mowing conditions. Fits wide range of tractors including high horsepower tractors. |
Star profile drivelines | Star profile spreads load out to many points on the shaft. More apt to resist bending and twisting under shock loads and harsh mowing conditions. |
Easy greasable drivelines | Drivelines have access holes for greasing the U-joints and to grease the inner profiles. |
4 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered. |
High blade tip speed |
540 rpm: Center: 17,377 fpm (88.3 mps), Wings: 17,329 fpm (88 mps) |
6" Blade overlap | Generous blade overlap eliminates skipping, especially in turns. |
High cutting capacity | Can cut brushy areas with saplings up to 3". |
10 1/2" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
3/16" Stump jumper backed with a 1" thick mounting bar |
Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough conditions. |
3/16" Deck thickness | Heavy enough to handle conditions but not weigh unit down. |
Self-leveling pull-type hitch | Reduces drawbar wear by keeping hitch level while going through ditches. |
LED Signal lights | LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts. |
Hinged wing section | Allow cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting. |
1" Solid hinge rods | Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself. |
Wing transport lock | Safety feature. Holds wing section up in case of hydraulic pressure loss. |
Enclosed front to rear dual leveling rods |
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
Drain holes in wheel rims | Allows water to drain from wheels mounted on the folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims. |
5" Square rear axle tubing | Heavy axle to handle harsh conditions. |
Spring-cushioned center-axle | Protects unit from bumps and ground shock. |
Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle. |
Double swivel hitch | Great for uneven terrain, reduces drawbar wear. |
Bar-tite hitch (optional) | Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
Wheel options | Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting & can’t go flat. |
Deck rings (optional) | 1/2" x 3" full welded deck ring keeps blades from damaging the deck. |
Specifications
Specifications & Capacities | RC5014 & RCM5014 |
Min. horsepower | 90 power take-off horsepower (67.1 kw) |
Gearbox horsepower | 250 (186.4 kw) Splitter 225 (167.8 kw) Center deck & wing deck |
Gearbox lubrication & capacity |
Center deck & wing: 10 pints (4.73 L) of gear lube 80-90W EP Divider gearbox: 5.5 pints (2.60 L) of gear lube 80-90W EP |
Cutting capacity | Up to 3" (7.6 cm) material |
Machine weight | 7,340 lbs. (3,329.4 kg) |
Blade tip speed At 540 rpm At 1000 rpm |
Center blade: 17,377 FPM (88.3 mps) & wing blade: 17,329 FPM (88 mps) Center blade: 18,165 FPM (92.3 mps) & wing blade: 18,317 FPM (93.1 mps) |
Tongue weight | 2,668 lbs. (1,210.2 kg) |
Hitch types | Standard clevis hitch, pintle hitch, ball hitch, LP performance hitch and bar-tite hitch |
Hitch jack | Standard hand crank |
Signal lights 7 Pin connector |
LED (standard) SAE J560 pin configuration |
Cutting width | SAE J560 pin configuration |
Cutting width Overall width Minimum transport width |
13'-6" (4.11 m) 15' (4.57 m) 8'-9" (2.44 m) |
Overall length | 19'-3" (5.87 m) |
Deck height | 10 1/2" (3.06 m) |
Cutting height* | 2" (5.1 cm) to 14" (35.6 cm) with hydraulic cylinder and stroke control spacers |
Lift hydraulics | 4" x 8" Hydraulic cylinder, hoses, fittings & stroke control spacers |
Wing hydraulics | 3 1/2" x 12" Hydraulic cylinders, hoses & fittings |
Wing transport protection | Wing transport lock |
Deck sheet thickness | 10g (3.4 mm) top and 10g (3.4 mm) bottom |
Side skirt thickness | 1/4" (6 mm) |
Wing deck skid shoes Center deck skid shoes Weight box skid shoe |
Replaceable Replaceable Replaceable |
Blades - 4 (2 per carrier) | 1/2" (13 mm) x 4" (10.2 cm) Heat-treated, free-swinging alloy steel with uplift |
Blade overlap | 6" (16.2 cm) |
Blade bolt | Keyed with hardened flat washer & locknut |
Stump jumper Blade holder |
3/16" (5 mm) Round dish shaped bolt-on stump-jumper (optional) 1" (2.5 cm) diamond shaped blade bar |
Deck rings (optional) | 1/2" (13 mm) x 3" (7.6 cm) fully welded |
Front & rear guards | Single chain or double chain |
Heavy duty Input driveline options | Constant velocity u-joint ASAE Cat. 6 with or without over running clutch |
Heavy duty Intermediate & wing drivelines | ASAE Cat. 5 with slip-clutch protection |
Tire & wheel options | 6" x 21" Laminated tires 6" x 26" Laminated tires 27" x 7.75" x 15" Used aircraft tires with foam filling 29" Used aircraft tires |
Number of wheel | 5 - Wheel option: 4 on transport axle and one on wing axle 6- Wheel option: 4 on transport axle and two on wing axle |
Transport axle | Spring-cushioned on center transport axle or optional walking tandem on center axle |
Hubs | Cast iron 5-bolt hubs with tapered roller bearings and with 1 3/4" (4.4 cm) shafts |